澳洲插座的吊力测试问题
3.14.8.2 Withdrawal force testThis test is applicable only to socket-outlets rated at up to and including 10 A, and intended for use with plugs of the type shown in Figure 2.1(a1). The test shall be applied to all the socket-outlets subjected to the test of Clause 3.14.8.1.
Plugs rated at 10 A and complying with Figure 2.1(a1) of this Standard and which have not been subjected to any previous tests shall be used. A separate plug shall be used for testing each socket-outlet.
Manually insert the plug fully into and withdraw it from the socket-outlet 10 times.
请问这个插入10次的插头插片的厚度是多少？是最厚的插片，还是最薄的插片？
Manually align the plug in the socket-outlet to minimize the effects of misalignment between mating components and any other friction-increasing factors, to attain the best practical position for minimum resistance to withdrawal.
NOTE: When testing in other than the horizontal plane, the mass of the plug and socket-outlet is to be considered in all measurements.
The plug is then fully reinserted and a withdrawal force gradually applied by any suitable means until the plug is fully withdrawn. The withdrawal force, during three subsequent and consecutive disengagements, shall be measured.
The withdrawal forces measured shall be between 20 N and 50 N.
请问这个测试的插头插片厚度又是多少呢？
希望专业人士帮忙解决，谢谢！
本帖最后由 ljh809809 于 2016-3-17 16:23 编辑
1，这两处所指的插头是同一个插头。第一处提到时是此插头之前没有在任何测试中使用过，第二处提到时是此插头已经经历过第一次提到时的插拔10次。
2，此插头的尺寸没有最大与最小公差之分，这一点与IEC 60884-1/GB2099.1第22.1.1章提到的“具有最大尺寸的试验插头。。。”不同，只要是满足figure a1的公差内即可。可以使用符合标准尺寸的商用插头。 ljh809809 发表于 2016-3-16 18:03 static/image/common/back.gif
1，这两处所指的插头是同一个插头。第一处提到时是此插头之前没有在任何测试中使用过，第二处提到时是此插头 ...
找了好多样品都发现一个问题，用带1.7厚的插片插头插入后再用普通插头进行吊力测试时都吊不起20N的砝码，如果用普通插头插拨10次吊时是没有问题的。
这样的产品合格吗？ 本帖最后由 ljh809809 于 2016-3-17 16:22 编辑
johnmark 发表于 2016-3-17 08:17 static/image/common/back.gif
找了好多样品都发现一个问题，用带1.7厚的插片插头插入后再用普通插头进行吊力测试时都吊不起20N的砝码， ...
如果你在插入插头之前证示插片厚度C确实在1.58mm与1.78mm之间，这也是与20N和50N的上下限值相对应的（IEC标准里针对多插销全部插入时只有最大拔出力）。然后测试时出现你描述的这种情况，就是不合格。 那插头的表面光潔度有要求嗎?
页:
[1]
