DSH 005/05 Luminaires provided with LEDs

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

DSH 005/05 # ?3 e( Z& L: n6 ~- G+ t0 a

Luminaires provided with LEDs

General Section 12

60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-2(ed.1);am1;am2 & 60825-1(ed.1);am1;am2

. c6 n# Z0 w' f# P+ |1 W. C0 qQuestion:
Is it possible to issue approvals on luminaires provided with LEDs light source?
Decision:
Yes, provided that:
# b- i; |) y- h  r* W- |. Y(1) The LED circuit is verified according to IEC/EN 61347-2-2 (*) or IEC/EN 61347-2-11. If the laser emits radiation in the wavelength range from 180 nm to 1 mm, the LED shall also be tested according to IEC/EN 60825 –1 (Safety of laser
products). Only LEDs classified as Class 1 lasers can be used without problems for lighting purposes without protection.
' `4 O* s; s; L5 e- m2 x% O& H(2) The thermal tests required in Section 12 of IEC/EN 60598-1 are carried out as follows:
2 d; C8 M) ~# C" Y! h4 n; L(a) Luminaires (Class I or II) with built-in control gear can be tested according to the requirements of IEC/EN 60598-2-6.
- M: b  a+ N) h  w+ o6 o* z; e(b) For Class III luminaires, the luminaires manufacturer shall provide on the instructions all the necessary information to supply the LED circuit correctly or shall inform the Testing Station about the trade mark, the type and the technical characteristics of the appropriate control gear. There can be three different control gears: the type and the trade mark indicated by the
luminaire manufacturer; an electronic control gear clearly specified on the luminaire instructions; a ferromagnetic control gear. The tests shall be carried out as required in Section 12 according to IEC/EN 60598-2-6 with the appropriate control gear.
# Y4 V% _, e( [4 J(*) When IEC/EN 61347-2-13 will be published, it will takes over IEC/EN 61347-2-2.

$ [$ h: u0 P3 x- B3 ~9 w
1 \; P* u. r7 A0 K

" B6 b: F# a/ G) N' C/ ]& v* y