PDSH 955 E14 lampholder used in lighting chains

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

PDSH 955 ! ^3 o* c( e9 D/ f6 ?$ t 6 ~# C3 d1 `) k- b

E14 lampholder used in lighting chains

20.7.1

60598-2-20(ed.3)

Standard(s):
IEC 60598-2-20/2010
+ S, i2 B" {# B+ g* s5 a, \0 ySubclause(s): 20.7.1
( T2 d5 ?& S: A: S5 P+ a) v  F$ ENo. Year PDSH 0955 2010
2 a% @7 Y: O. O4 x2 I, u, `Category: LITE Developed by: ETF5 OSM/LUM
Subject:
E14 lampholder used in lighting chains
/ v3 L: y/ M& Z* F/ yKey words:
- x. A0 B& v- J# _1 Q- E14 lampholder
: W" k5 o. J  l3 W1 a9 H' g- Lighting chain
- IEC 60238
To be approved at the 49th CTL Plenary Meeting, in 2012
Question:
0 Q. _$ @' E5 ^  c6 H- Clause 20.7.1 of IEC 60598-2-20 requires that Edison screw lampholders E10, E14 and E 27 shall
meet the requirements of IEC 60238.
* V9 |# q- ^- q$ T# R7 b- Clause 8.2 of IEC 60238 requires that lampholder shall be tested according to the gauges 7006-30
7 J2 D- O; K& z(7006-30A for candle lampholder) and 7006-31.
# g+ G; H" k6 ^9 gIn the case shown in photos 1 and 2, the only possibility to fulfill the requirements with gauge 7006-30 is
to cut the gasket around the rim of the lampholder. However in this condition the lampholder does not
9 ^- T: `9 U/ u0 M1 Y6 n& ]% f7 r2 afulfill the requirement of 7006-31 for protection against electric shock. In the note after the fourth
' P; `( M9 t  F( x; @; u- w3 Yparagraph of clause 20.12.1 of IEC 60598-2-20 it is written that the gasket may serve as protection against
accidental contact with the cap of the lamp, but only for bayonet lampholder. So, it is not applicable to the
E14 lampholder.
In the case shown in photo 3 the test with gauge 7006-31 gives negative result.
In the two cases, the lampholders have been designed to accept E14/20 lamp cap only (and not E14/23x15
5 q- K2 d/ X: E& N5 p6 wor E14/25x17). So, if the tests are performed with these kind of lamps, the test requirements are fulfilled.
We think that this lampholder used in a lighting chain is not in compliance with the standard due to the
requirement of clause 20.7.1. What is the opinion of the other laboratories?
Decision:
The lampholder can be accepted as part of lighting chain / luminaire. All requirements according to IEC
' X+ Z8 g3 m8 F/ ^1 L60238 as far as applicable have to be fulfilled and the gauge 7006-31 shall comply.
8 b8 _- g2 T1 O; w( G


# g+ y" W6 b: x9 l) {+ t


1 L. a( O. h1 ~0 ]% o! G  Y* T