UL火线零线的颜色

jsspace

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

产品是筒灯，输入线黑色和白色。
白色是零线，黑色是火线，这个说法是正确的吗？
; J+ d- l# R: W, s  A

fasten

jsspace 发表于 2015-12-25 12:25
- u1 z; W1 s* H0 X, x5 s% v1 S其实有规定的，我看到UL1598上有写明白色的是零线，火线的颜色没有规定，跟零线不同即可

谁敢说没有规定的？
2 o% e& |3 N4 Z$ }& \6.10 Identification and polarity
. Q- Z. Y8 b: s6.10.1 A conductor terminal intended for the connection of the neutral conductor of the branch circuit shall be substantially white in color or be marked neutral adjacent to the terminal in accordance with Table 20.1.1, Item 1.5.
6.10.2 The insulation on a conductor intended for connection to the neutral conductor of the branch circuit shall be identified by one of the following means:
, `. |2 G0 e% x/ t5 H(a) be colored white or grey;
(b) be of any color except green, with a continuous white tracer throughout its length;
(c) be identified at the point where connected to the branch circuit by white paint, tape, ink, or permanent tag; or
7 J# N% x% u! @, Q4 N" {& l8 t4 W(d) be provided with one or more raised longitudinal ridges, if a parallel conductor flexible cord.
6.10.3 The identified terminal of a wiring device shall be connected to the neutral conductor of the branch circuit.
6.10.4 A cord-and-plug-connected luminaire equipped with a polarized two-pole, two-wire parallel blade attachment plug shall be marked for proper polarity in accordance with Table 20.1.1, Item 4.5.

如沐春风

是的，我们出口美国的产品都是这样标记的

brent

是沒有標準規定,只有行業認定. 深色火線,淺色零線

edwardlds

学习。。。

jsspace

brent 发表于 2015-12-25 11:04
% v- G8 q4 K3 }4 l  y; f4 V- x# X是沒有標準規定,只有行業認定. 深色火線,淺色零線

6 K. I7 ~4 L0 \% @. V% ^其实有规定的，我看到UL1598上有写明白色的是零线，火线的颜色没有规定，跟零线不同即可

head0819

我们还是参考一下UL62 Flexible Cords and Cables

fasten

head0819 发表于 2015-12-25 13:08
1 r  @9 l  v. r7 g我们还是参考一下UL62 Flexible Cords and Cables

+ G+ y6 @) H, c( {& z6 L其实所有这些所谓的白色/灰色是零线的要求要回到：NFPA 70 第200.6节要求：
4 K% l- M1 t, W" [2 B. E9 c200.6 Means of Identifying Grounded Conductors.
(A) Sizes 6 AWG or Smaller. An insulated grounded conductor
of 6 AWG or smaller shall be identified by one of
) {, r  t: ?3 I% I& athe following means:
(1) A continuous white outer finish.
0 ?& \6 b0 h3 R. h$ e0 R(2) A continuous gray outer finish.
(3) Three continuous white or gray stripes along the conductor’s
& D  B! Q# H5 K* s/ o3 z1 Gentire length on other than green insulation.
(4) Wires that have their outer covering finished to show a
* D8 `1 w* b: Awhite or gray color but have colored tracer threads in
0 I. e+ |. l6 B: s" _& s. H) D1 tthe braid identifying the source of manufacture shall be
considered as meeting the provisions of this section.
(5) The grounded conductor of a mineral-insulated, metalsheathed
+ u  g) _( _8 L- h$ ~cable (Type MI) shall be identified at the time of
0 r6 ^6 j0 x" i" g/ ^installation by distinctive marking at its terminations.
3 ~& K; R; ^3 m* g. k; Y(6) A single-conductor, sunlight-resistant, outdoor-rated
; F) a4 s* E, F+ g- Q, U3 ncable used as a grounded conductor in photovoltaic
power systems, as permitted by 690.31, shall be identified
at the time of installation by distinctive white
6 h$ ?5 }8 v8 S; X: Rmarking at all terminations.
(7) Fixture wire shall comply with the requirements for
grounded conductor identification as specified in 402.8.
2 `3 |# c4 m) ^, l0 J" S& h(8) For aerial cable, the identification shall be as above, or
by means of a ridge located on the exterior of the cable
so as to identify it.

(B) Sizes 4 AWG or Larger. An insulated grounded conductor
( w% s+ V; ~, J6 Q9 k4 AWG or larger shall be identified by one of the
following means:
% ?3 `1 [: p- p(1) A continuous white outer finish.
(2) A continuous gray outer finish.
& p  n: N! q: Z) b+ k8 d6 v4 K(3) Three continuous white or gray stripes along the conductor’s
entire length on other than green insulation.
(4) At the time of installation, by a distinctive white or
gray marking at its terminations. This marking shall
6 _2 c6 ?# Q/ l0 E" `: k1 X0 [encircle the conductor or insulation.
8 h! I/ z5 Y& q6 Y(C) Flexible Cords. An insulated conductor that is intended
for use as a grounded conductor, where contained
. @/ Z6 G8 Z) I/ Y! C# hwithin a flexible cord, shall be identified by a white or gray
outer finish or by methods permitted by 400.22.
(D) Grounded Conductors of Different Systems. Where
grounded conductors of different systems are installed in
7 I8 U8 K5 Q  Q: C; [the same raceway, cable, box, auxiliary gutter, or other type
of enclosure, each grounded conductor shall be identified
by system. Identification that distinguishes each system
" W8 M2 D# A) v$ A$ e0 @6 ~grounded conductor shall be permitted by one of the following
0 y2 A4 A; m& R8 n2 e2 F; F1 L) ^- ^means:
(1) One system grounded conductor shall have an outer
covering conforming to 200.6(A) or (B).
(2) The grounded conductor(s) of other systems shall have
a different outer covering conforming to 200.6(A) or
1 M3 F% a, D; Z- G1 r200.6(B) or by an outer covering of white or gray with
a readily distinguishable colored stripe other than green
running along the insulation.
(3) Other and different means of identification as allowed
by 200.6(A) or (B) that will distinguish each system
! l, j; i& a" @9 |grounded conductor.
4 C$ L+ J- D/ W$ ?9 [6 B* |2 Y. hThe means of identification shall be documented in a
manner that is readily available or shall be permanently
- y0 C; `7 b; F' `posted where the conductors of different systems originate.
(E) Grounded Conductors of Multiconductor Cables. The
insulated grounded conductors in a multiconductor cable shall
be identified by a continuous white or gray outer finish or by
three continuous white or gray stripes on other than green
insulation along its entire length. Multiconductor flat cable
! f8 G0 W% ^8 i3 A; \4 AWG or larger shall be permitted to employ an external
" N( J! q+ I6 |: ?ridge on the grounded conductor.
Exception No. 1: Where the conditions of maintenance and
! K3 V4 y+ ^1 ?! h$ I/ h' W! isupervision ensure that only qualified persons service the installation,
grounded conductors in multiconductor cables shall
be permitted to be permanently identified at their terminations
: I* X/ ^" N$ V% n4 n7 ]$ lat the time of installation by a distinctive white marking or
other equally effective means.
/ q4 j5 d! B% d; w/ B+ |9 S7 KException No. 2: The grounded conductor of a multiconductor
varnished-cloth-insulated cable shall be permitted to be

! ^, O+ A% B1 cidentified at its terminations at the time of installation by a
7 e1 e6 f- Q6 _- Pdistinctive white marking or other equally effective means.
Informational Note: The color gray may have been used in
, M: E0 a8 O) R' }1 Dthe past as an ungrounded conductor. Care should be taken
when working on existing systems.
1 T& E. J, T$ `) U8 J

9 h& S( d# y% N- g2 Z- d  S有兴趣的可以看看。Grounded就是说的Neutral。你所列的UL62要求就是200.6 (C)要求。

guanito

美标白色线是零线，绿色线是地线，其电颜色线作相线，优先采用黑线

c382260622

还好路过，学习了