UL 1310对变压器绝缘材料打耐压有没有层数方面的描述？

信思哲

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

L 1310对变压器绝缘材料打耐压有没有层数方面的描述？clause 40中对绝缘层打耐压我该怎么操作呢？是按照1层打，还是按照总厚度大？

40 Tests on Insulating Materials
; O7 Q% z! O5 c$ c8 K
40.1 If required by 13.2.1(b), 13.2.2(c), 13.2.5(c), 13.2.6(c), 13.2.10(b), insulating material shall be
subjected to the test described in 40.2.
; R9 l0 b; e' E, {$ p, M7 `
Exception: The insulating material need not be subjected to this test if it is generic material noted in 40.3
and Table 40.1.
5 p. n2 F: U9 g$ n: P, H5 O8 O/ N, c
3 i* Z1 x. y, a1 _( j7 M40.2 The insulating material is to be placed between two opposing electrodes. The electrodes are to be
cylindrical brass or stainless steel rods 1/4 inch (6.4 mm) in diameter, with edges rounded to a 1/32-inch
. h, h6 O- {8 x" B9 V& a! ^  Y(0.8 mm) radius. The upper moveable electrode is to weigh 50 ±2 grams to exert sufficient pressure on
the specimen to provide good electrical contact. The test potential is to be increased to the test value and
5 c- \# t" y+ Q9 @  u$ D1 Ithe maximum test potential is to be maintained for 1 second. The result is acceptable if there is no
dielectric breakdown.

* s- U( ~  e, x0 F: u/ N
. Y# |- p* |( d1 a# u
我看60950和62368的有详细的描述，还是直接引用这个打法呢？

60950-1 ©IEC:2005+A1:2009  +A2:2013

1 c' ~, y* a0 x2 B) h: }

2.10.5.10 Thin sheetmaterial - alternative test procedure

If layers can beseparated for individual testing, the following alternative to the standardtest

procedure in2.10.5.9 is permitted.

Electric strengthtests are applied in accordance with 5.2.2, using test voltages equal to the

test voltagespecified in 5.2.2 for SUPPLEMENTARY INSULATION or REINFORCED INSULATION as

appropriate.

If two layers areused, each layer shall pass the test.

If three or morelayers are used, each combination of two layers together shall pass the test.

If three or morelayers are used, It is permitted to divide these layers into two or threegroups

for testingpurposes. In the above electric strength tests, two or three groups are tested

instead of two orthree layers.

A test on a layer orgroup of layers is not repeated on an identical layer or group.

6 y& Y  u" [& k: a; b* _. I

62368-1 © IEC:2014

) k* A; n0 A* f6 a8 Y& U" E

5.4.4 Solidinsulation

5.4.4.6 Thin sheetmaterial

, [9 |: e" v+ m$ A# P- D

5.4.4.6.4 Standardtest procedure for non-separable thin sheet material

For non-separablelayers, electric strength tests are applied in accordance with 5.4.9.1 to all

layers together. Thetest voltage is:

− 200 % of Utestif two layers are used; or

− 150 % of Utestif three or more layers are used,

where Utest is thetest voltage specified in 5.4.9.1 for supplementary insulation or

reinforcedinsulation as appropriate.

chenke520

谢谢分享

beidalongdi

谢谢分享

waterssj

虽然我也不知道，但楼上的，这是提问，不是解答