新西兰官方关于澳洲认证

fasten

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

How to comply
Step 1: Ensure products meet an appropriate standard
Lists of applicable standards are prescribed in the
* o3 M# u0 w; t) S7 T

[li]Radiocommunications (EMC Standards) Notice [32 kB PDF] and
6 q% \+ n+ G$ r+ c4 u3 x[/li][li]Radiocommunications (Radio Standards) Notice 2007
[/li]

Copies of applicable standards can be obtained from Standards New Zealand or Standards Australia.  Suppliers should consult a testing laboratory for technical advice regarding applicable standards.
The supplier must determine which level of conformity from the Radiocommunications (Compliance) Notice 2004 [164 kB PDF] applies to each product and conduct compliance actions accordingly.  Advice regarding obligations imposed by the Notice should be sought from the supplier’s legal advisor.
These flow charts will help provide guidance for electrical and electronic product suppliers:
/ j+ f; T+ s; d) e+ F" Z

[li]Radio compliance flowchart
: s# b. y# M" R1 N[/li][li]Electromagnetic compatibility flowchart
[/li]

3 i: q; E3 R% _0 MStep 2: Prepare a product description
6 v" p  I4 ^3 H% n- K0 g" u  F+ VA product description of the marketed product identifies its use, brand name, and model number (at a minimum).  A photo and technical description can also be supplied.
6 ]( [3 v! f* D$ m: G% m

Step 3: Prove compliance through testing
The supplier accepts total responsibility for product conformity and needs to make a commercial decision on the level of testing required.
A test report or manufacturer’s specification may be sufficient evidence to support a declaration that the product meets a relevant standard recognised by RSM.  For level of conformity 3 products, a test report from an accredited laboratory (which may be in NZ or overseas) is required.  The test report must be in English. The supplier does not have to hold the original of the test report.  A clear copy of the original is acceptable.


! U+ Q: l3 E1 p, i4 e! oStep 4: Make a Supplier’s Declaration of Conformity (SDOC)
- `' I. O# i; I' ?! wThe Supplier's Declaration of Conformity (SDOC) is the document signed by a New Zealand supplier or a New Zealand agent of an overseas manufacturer or supplier to certify that a product meets applicable standards.


9 ]& W. E0 w) O2 ]# O7 K. }, P; s
  f1 r, f* l: z4 qStep 5: Create a compliance folder
Compliance folders are a collection of documents assembled by the supplier to support the compliance declaration.  A compliance folder contains:

[li]a product description
[/li][li]a signed Declaration of Conformity
( }8 Q( D& [8 @' o9 b) o  @9 {8 E[/li][li]a test report or other documented evidence of conformity (mandatory for levels 2, 3, A2, and A3 products).
[/li]

Step 6: Apply for a Supplier Code Number (SCN)
Supplier Code Number (SCN) is a registration number obtained from RSM free of charge.  It authorises the holder to use the C-tick compliance mark.  A New Zealand Supplier Code Number consists of the letter “Z” and a unique numerical identifier.



/ B  c8 P8 l) y# XStep 7: Label the product
A label indicates that the product complies with the applicable standards and establishes a traceable link between a product and the supplier responsible for placing it on the market.
$ \; o! ?8 |5 b8 ~' n0 @2 v% zWhere a product is in a class to which level of conformity 1, 2 and 3 applies, the compliance label consists of:
: D2 E6 Y1 a5 F* h* ^. t1 C5 F7 k

[li]a compliance mark such as C-Tick[sup]1[/sup] or RCM, and [/li][li]an unique supplier identification such as the Supplier Code Number [/li]

Where a product is a radio transmitter in a class to which level of conformity A1, A2 or A3 applies, the product must be labelled with a New Zealand supplier code number only.
+ E- `* S3 R( x: \3 k+ g$ TThe label must be legibly and durably applied on the external surface of the product.  The compliance mark must be no smaller than 3mm in diameter and the supplier identification characters must be no less than 1mm in height.

http://www.rsm.govt.nz/cms/product-compliance/suppliers/how-to-comply
$ T( `) `2 o1 L/ ^1 Zhttp://www.rsm.govt.nz/cms/pdf-l ... nce-notice-2004.pdf

yaya

顶上，

wwwabcd

thanks for sharing