安规网

 找回密码
 注册安规
安规论坛 | 仪器设备 | 求职招聘 | 国家标准 公告 | 教程 | 家电 | 灯具 | 环保 | ITAV 签到 充值 在线 打卡 设备 好友| 帖子| 空间| 日志| 相册
IP淋雨机 | 证书查询 | 规范下载 | 资质查询 招聘 | 考试 | 线缆 | 玩具 | 标准 | 综 合 红包 邮箱 打卡 工资 禁言 分享| 记录| 道具| 勋章| 任务
IP淋雨设备| 恒温恒湿箱| 拉力机| 医疗检测设备沙特Saber 埃及COI 中东GCC|CoC直接发证机构水平垂直燃烧机|灼热丝|针焰试验机|漏电起痕试验机
灯头量规|试验指|插头插座量规|灯具检测设备耐划痕试验机|可程式恒温恒湿试验箱 | 耦合器设备广东安规-原厂生产-满足标准-审核无忧
查看: 2004|回复: 7

[美洲标准产品] UL产品的电线警告标签(求助)

[复制链接]
发表于 2010-1-18 14:17 | 显示全部楼层 |阅读模式
广东安规检测
有限公司提供:
我公司有款取暖器 送UL做认证时 要求在电源线上加警告语标签 哪位DX帮帮忙 应该做成什么规格 内容有什么要求吗?在线等
发表于 2010-1-18 14:38 | 显示全部楼层
UL817 PROCEDURE SECTION GENERAL 要求:3 G4 j9 n3 P" x( w: r) H+ x# M2 B+ B
    美規US Type 電源線AC Cord, 根據UL817規定從去年2006.06.24 就開始要求, 如下文及附件:$ h/ \  ?5 P3 `& B3 y* [  K: `0 p3 _

( n2 W& Y) G9 Q/ E "Detachable Power Supply Cords intended for shipment to Original Equipment Manufacturers, shall have any applicable makings provided on the outer surface of the shipping carton, or on a tag or the equivalent inside the carton.  For Detachable Power Supply Cords intended for shipment to original equipment manufacturer, the electrical rating shall be on a tag, or an equivalent, on each individual Detachable Power Supply Cord unless the ampere rating of the flexible cord is equal to or greater than the ampere rating of the attachment plug."
8 S3 D. P+ q* h/ D作法:
  L! a/ M3 p1 {* q將有電氣額定規格electrical rating標籤 貼在電源線上
! Q/ ~$ t7 I3 F9 L* Q標籤內容字體除高度規定至少1.6mm及字體清晰可見, 標示電流須取最小電流 A 值標示, 範例如下:: i% J6 x+ [! K# M
先核對''UL報告'' 中插頭Plug及尾插Connector及電線cord的通過測試的電流值2 S; |3 d! @) O0 o
Example: NEMA 1-15Plug(15A) + IEC C7 Connector(10A) + No. 18 AWG Flexible Cord(10A): r: [& Q8 G! M! I- F3 @0 l
4 E* p/ w3 L3 x( j, U
因為這要求是UL對電源線廠的要求, 電源線廠有義務責任提出符合UL要求的電源線,
发表于 2010-1-18 15:05 | 显示全部楼层
多谢楼上的。
发表于 2010-1-19 12:58 | 显示全部楼层
取暖器是 按照 UL 1278做的吧,如果是最新版本的1278,则需要下面的警告语句,以tag 的形式:2 Y! X) D- m5 p! b' F& }! H

# Y3 Q* H3 P4 s) P8 w+ q) F3 [6 ^
“WARNING – TO REDUCE THE RISK OF FIRE:4 e; x7 P  Q: y# L# B
1) Do not place any objects such as furniture, papers, clothes, and curtains closer than% M4 u7 M, D' k
3 feet (0.9 m) to the front of the heater and keep them away from the sides and rear
2 j  J3 E  ~8 X) A1 ~when the heater is plugged in.
6 h; a9 ~' P! L' O. u2) Do not place the heater near a bed because objects such as pillows or blankets can
) K  W- g% m) }4 Lfall off the bed and be ignited by the heater.
% t" G8 h3 a; H7 \3) Always unplug heater when not in use. (This item may be omitted if the heater is  |. @$ L/ d0 Q2 B9 L0 f% g
provided with a clock-operated switch).7 }. D5 q8 z# Z
4) Always plug heaters directly into a wall outlet/receptacle. Never use with an) i5 x% _5 ^4 u1 i; R' x# A% _0 }
extension cord or relocatable power tap (outlet/power strip).
: ^9 S! }4 G7 n6 m- M) ?5 Y5) Do not operate heater with a damaged cord or plug or after the heater malfunctions,
4 T* o4 I: c: ?( b# u' S/ d% E5 Rhas been dropped or damaged in any manner. Discard heater or return to an1 `6 J& o% P% s' }, E
authorized service facility for examination and/or repair.
; ~3 w! f. G5 X) n/ E. R% u6) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
/ v2 A: |' W/ {: A( Q) A! ^similar coverings. Do not route cord under furniture or appliances. Arrange cord away
* u( `( S3 ]6 u4 I- bfrom traffic area and where it will not be tripped over.7 [$ n! H* w* q$ m3 ^
7) Check your heater cord and plug connections.
1 Z1 |: I) |4 r  u  i/ Ma) Faulty wall outlet connections or loose plugs can cause the outlet or plug to5 q+ K- Y( r4 w; X( Z
overheat. Be sure the plug fits tight in the outlet.
, l- O2 r  r7 U5 o) Zb) Heaters draw more current than small appliances, overheating of the outlet
3 W0 O! |, k" m: E3 Rmay occur even if it has not occurred with the use of other appliances.
" Q  ?+ S- j% O( ]6 N9 k7 oc) During use check frequently to determine if your plug outlet or faceplate is4 g* [5 K- d, q3 {
HOT!
& Z) O! z/ L" q5 U8 Xd) If so, discontinue use of the heater and have a qualified electrician check
0 O$ E1 ~$ {' Z2 C# p  gand/or replace the faulty outlet(s).4 t" Y1 q2 Z. A4 Y  ?
DO NOT REMOVE THIS TAG!”2 ]7 u7 J+ z  X& Q2 w$ }

* K2 w5 w6 G  r! i. o
" d' P* f6 h, q0 z* i% H$ e+ N2 N2 ?; c2 m3 ~4 R% \7 M
2楼的回答,为线方面的,整体并不需要考虑2 f3 S  t: y5 l+ N
尺寸要求如下:
/ I! y  |" h! ^0 h) b3 f7 I' R) Y0 C$ f9 `& c8 e0 r) I
9 J+ [7 s3 p' p$ i3 z7 N
The statements ²WARNING – TO REDUCE THE RISK OF FIRE² and
! M  u0 t; b# I: S1 K+ K1 W; N²DO NOT REMOVE THIS TAG!² shall be in letters at least 3/16 inch (4.8 mm) in height. The2 ]0 j  G4 q- @5 o7 a& @/ h  r
remaining text shall be in letters of at least 1/16 inch (1.6 mm) in height.( ~7 f% l  _6 C8 H* \7 B: \
; a9 B; g$ G- ^5 ?% w9 @
这个 tag需要进行相关测试,可以参考ul 1278的要求
发表于 2010-1-19 13:07 | 显示全部楼层
也就是标明电流、电压
 楼主| 发表于 2010-1-19 13:25 | 显示全部楼层
谢谢DX  正如3楼讲解的 客户那边沟通后 给出的要求类似
发表于 2010-1-20 11:26 | 显示全部楼层
UL的tag有明确要求的  
发表于 2010-1-21 23:01 | 显示全部楼层
其实做ETL 好点,ETL 报告上都列出了所有标签的要求,同时价格会便宜些。我们工厂的产品客户没有特许要求就做ETL
您需要登录后才可以回帖 登录 | 注册安规

本版积分规则

关闭

安规网为您推荐上一条 /2 下一条

QQ|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网 ( 粤ICP13023453-10 )

GMT+8, 2024-12-18 22:42 , Processed in 0.088803 second(s), 20 queries .

Powered by Discuz! X3.4

© 2001-2023 Discuz! Team.

快速回复 返回顶部 返回列表